-
1 линейно изменяющаяся нагрузка
линейно изменяющаяся нагрузка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Русско-английский словарь нормативно-технической терминологии > линейно изменяющаяся нагрузка
-
2 работа с переменной нагрузкой
Русско-английский большой базовый словарь > работа с переменной нагрузкой
-
3 распределённая нагрузка, изменяющаяся по линейному закону
Engineering: distributed load with linear variation, linearly varying loadУниверсальный русско-английский словарь > распределённая нагрузка, изменяющаяся по линейному закону
-
4 линейно изменяющаяся нагрузка
Engineering: linearly varying loadУниверсальный русско-английский словарь > линейно изменяющаяся нагрузка
-
5 нагрузка, изменяющаяся по линейному закону
Construction: linearly varying loadУниверсальный русско-английский словарь > нагрузка, изменяющаяся по линейному закону
-
6 импульсный источник электропитания с коммутацией тока на первичной стороне
импульсный источник электропитания с коммутацией тока на первичной стороне
-In primary switch mode power supplies, the AC mains voltage is first rectified and smoothed and then chopped ("switched"). Chopping means that the DC voltage is switched periodically at a frequency of 40 to 200 kHz using a power transistor.
In contrast to linearly regulated power supplies, the power transistor does not act as a variable resistor but as a switch instead. This generates a square-wave AC voltage that is transformed to the secondary circuit using a high-frequency transformer. In the secondary circuit, the voltage is rectifi ed and smoothed. The quantity of energy transformed to the secondary circuit is controlled, depending on the load, by varying the chopping rate. The longer the transistor is conductive, the higher is the quantity of energy transformed to the secondary circuit ( pulse width modulation).
Due to the use of high-frequency AC voltage, primary switch mode power supplies have the decisive advantage that their transformer can be of much smaller size than required for the transformation of low frequencies. This reduces the weight and the dissipation inside the unit. The effi ciency of these units is between 85 and 95 %. Since the output voltage does not directly depend on the input voltage, these units can be used for a wide input voltage range and can even be supplied with DC voltage. Furthermore, it is possible to buffer short-time mains voltage breakdowns up to 200 ms. However, the power failure buffering time is limited by the size of capacitor C1 since a longer buffering time requires a higher capacity and thus a bigger size of the capacitor. Especially in case of small power supplies this is not desirable.
Therefore, a practicable compromise has to be made between the size of the power supply and the buffering time.
Primary switch mode power supplies can be used for all purposes. For example, they are suitable for the supply of all kind of electronics as well as for electromechanical applications.
[ABB]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > импульсный источник электропитания с коммутацией тока на первичной стороне
См. также в других словарях:
линейно изменяющаяся нагрузка — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] Тематики электротехника, основные понятия EN linearly varying load … Справочник технического переводчика
Shear and moment diagram — Shear and bending moment diagrams are analytical tools used in conjunction with structural analysis to help perform structural design by determining the value of shear force and bending moment at a given point of an element. Using these diagrams… … Wikipedia
Shear and moment diagrams — Shear and bending moment diagrams are analytical tools used in conjunction with structural analysis to help perform structural design by determining the value of shear force and bending moment at a given point of an element. Using these diagrams… … Wikipedia
Transformer — This article is about the electrical device. For the toy line franchise, see Transformers. For other uses, see Transformer (disambiguation). Pole mounted distribution transformer with center tapped secondary winding. This type of transformer is… … Wikipedia
Maglev — JR Maglev at Yamanashi, Japan test track in November 2005 … Wikipedia
Network analysis (electrical circuits) — Linear Network Analysis Elements … Wikipedia
Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… … Wikipedia
Viscoelasticity — is the property of materials that exhibit both viscous and elastic characteristics when undergoing deformation. Viscous materials, like honey, resist shear flow and strain linearly with time when a stress is applied. Elastic materials strain… … Wikipedia
List of Tesla patents — Below is a list of Tesla patents. Dr. Nikola Tesla was an inventor who obtained around 300 patents [Snezana Sarbo, [http://www.tesla symp06.org/papers/Tesla Symp06 Sarboh.pdfNikola Tesla s Patents] , Sixth International Symposium Nikola Tesla,… … Wikipedia
Ripple (electrical) — The most common meaning of ripple in electrical science, is the small unwanted residual periodic variation of the direct current (dc) output of a power supply which has been derived from an alternating current (ac) source. This ripple is due to… … Wikipedia
Bicycle and motorcycle dynamics — A computer generated, simplified model of bike and rider demonstrating an uncontrolled right turn. An … Wikipedia